DME TRANSPONDER ANTENNA/BNC Female Connector, Extended 2 Stud Mount, .70 Stud Length, 960-1220 MHz and 1030-1090 MHz, 50 Ohms, Airspeed 400 Knots & a White Finish
The CI 105-16 is a broadband and rugged antenna designed for DME or transponder use. The antenna assembly is designed specifically as a replacement for the Honeywell Bendix-King KA60 and offers an extended length, two-stud mounting that is found on the KA60. It includes a BNC connector and covers 960 MHz to 1220 MHz frequencies and is rated to 400 Knots TAS at 70,000 feet.
A200-HMS – Slick/Unison Rotational Speed Sensor
The A200-HMS is an Hall Effect rotational speed sensor. It provides a speed accuracy of 1 RPM when used in conjunction with the TM200 instrument.
The output signal is a latched, pulse width modulated square wave output of 0V to a maximum of 30V, proportional to rotational speed.
Power requirements are 3.8V to 30V / 3mA.
Precision machined from 6061 T6 aircraft grade aluminum, this sensor is designed to thread into the vent hole of Slick/Unison unpressurized magnetos.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this speed sensor is STC'd as a primary replacement.
TY96/TY97 Mounting Tray, Installation Kit and Manuals
RAMI AV-587 Antenna Accessories | Diplexer, Splitter
Trans-Cal Altitude Encoder SSD120-35C-RS232
IBBS Replacement Batteries (3ah and 6ah)
LiFe battery pack replacement for the Integrated Battery Back-up System. IBBS replacement batteries are available for all Experimental and Certified IBBS models.
Select options
This product has multiple variants. The options may be chosen on the product page
A200-TSA Outside Air Temperature Sensor
The A200-TSA is a monolithic temperature sensor with on-chip signal conditioning and an operating temperature of -50°C to 150°C. It has an accuracy of +/- 0.5°C over the full operating range.
The output voltage is proportional to the temperature x the supply voltage (ratiometric). The output swings from 0.25 V at −50°C to +4.75 V at +150°C using a single +5.0 V supply.
The temperature transfer function is:
VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA]
Power requirements are 5V / 1mA.
The sensor has a 5/16-24 threaded body and is supplied with two nylon mounting washers and a Nyloc fastening nut.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this temperature sensor is STC'd as a primary replacement.
Variable Intensity Lighting Controller
Variable Intensity Lighting Controller - REV 1 Instrument ONLY
NOTE: This item is only required for use on products purchased BEFORE 03-JAN-2013
ONLY USE THIS ITEM TO REPLACE AN EXISTING REV A UNIT IF IT HAS FAILED.
Products manufactured after this date have this unit INCLUDED and are connected to the panel lighting system or a separate potentiometer.
The A200-DDC Intensity Controller will support up to ten Rev 1 instruments in a single installation. It provides infinitely variable, uniform intensity control for all instruments.
These units are TSO qualified with all 200 Series instruments and is STC'd as a primary replacement instrument component under all flight conditions (day/night VFR and IFR).
CI 105 DME TRANSPONDER ANTENNA/BNC Female Connector, L-Band, 960-1220 MHz and 1030-1090 MHz, 50 Ohms, Airspeed 400 Knots, cork gasket included, 2 Hole Mount & a White Finish
The CI 105 is a broadband and rugged antenna designed for DME or transponder use. The antenna assembly is encased in a glass reinforced polyester molded shell and has a standard two stud mounting configuration. It includes a BNC connector and covers 960 MHz to 1220 MHz frequencies and is rated to 400 Knots TAS at 25,000 feet.
