Optimate TM-275 9.5amp Battery Charger/Maintainer/Power Supply (12-13.2V Batteries)
$189.99
This Optimate Plug in the Wall Lithium charger will quickly charge your battery at 9.5 amps, maintain it at the optimal voltage, and can be used as a power source of 5 continuous amps! For example, you can use it as power supply while programming your aircraft EFIS so you are not draining your battery while you work.
Features:
- CHARGER
- MAINTAINER
- POWER SUPPLY (press TUNE Button)
What’s included:
- 1 x TM-275 charger/maintainer/power supply
- 1 x battery alligator clips
- 1 x waterproof quick connect lead with ringlets and SAE connector
High efficiency diagnostic charger and tester for LiFePO4 / LFP batteries.
Perfect for charging of a high performance 12.8V-13.2V LiFePO4 / LFP battery sized from 2.5 to 120 Amp-hour.
Special features:
* TUNE mode delivers stable power for vehicle system reprogramming, show room vehicle demo or retaining memorized settings when battery cables are disconnected to fit powered accessories or replace the battery.
* BMS reset, pushbutton activated – for batteries with resettable low voltage / deep discharge protection.
* Battery SAVE mode with BMS reset : starts from 0.5V with continuous monitoring / testing of charge acceptance or bad / shorted cell condition. Unnecessary (and unsafe) charging of a bad battery is prevented.
* safeTº : Automatic charge rate adjustment to ambient temperature sensed at the charger. Reduced charging below freezing, no charging if temperature is below -20ºC/-4ºF (can damage lithium batteries).
* Ampmatic : Microprocessor adjusts current to ideal LiFePO4 charge curve to match battery size / condition, for fastest and most complete charge.
SAVE : Low Volt Start of 0.5V + 3-step low volt SAVE and TEST
Technical Specifications
- Recommended for LiFePO4 batteries: up to 120Ah
- Operation: Fully automatic
- Charging amps: 9.5
- Charging volts: 12.8V (nominal) 0.5V – 14.4V (range)
- Charge time limit: 24 hours (maintenance time: unlimited)
- Maintain/test cycles: 30 min/30 min (alternating hourly)
- Safe: No risk of overcharging. Totally safe for vehicle electronics. Sparks suppressed. Safe for long-term battery maintenance. Automatic shut-down if short-circuited or battery disconnected
- Style: Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector
- Operation temperature range: -40°C – +40°C
- Warranty: 3 years
| Weight | 0.1 lbs |
|---|---|
| Dimensions | 0.1 × 0.1 × 0.1 in |
| Brand | EarthX Batteries |
SHIPPING INFORMATION
We can ship by UPS, or USPS and DHL Express. We ship nationally, and internationally.
Carriers In Use
SHIPPING COSTS
- International Shipping Quote has to be done manually due to dimensions, weight, end destination, and more. Please E-Mail us.
- Any manner or method is available, call if you need Priority 1-2 day or overnight shipping.
- We are shipping with UPS or USPS and DHL Express
Related products
ETX-JMP12/24 12V-24V Jump Pack (All-In-One)
This is a 12V/24V jump pack that can boost just about anything! Very compact and the entire kit is only 4 pounds. This jump pack uses the technology of lithium iron phosphate (LiFePo4) chemistry, not Lithium Cobalt (LiCoO2). LiFePo4 is the most powerful, safest and most robust of all the lithium chemistries, plus double the life span of lithium cobalt packs.
Examples of what it can jump start: automobiles, diesel trucks, motorcycles, boats, construction equipment, experimental and certified aircraft, tractors, snowmobiles, ATV/UTVs, riding lawnmowers, and so much more.
BB-TH-CO Thermal Battery Box “C” Case
Thermal battery box to protect from radiated or convection heat. Compatible with our existing “C” case battery models; ETX680C.
The EarthX thermal battery box is designed to protect the battery in engine compartment installations from periods of high temperature (up to 1 hour), such as after shutdown, and from radiant heat from hot surfaces like exhaust systems during and after flight. This stainless-steel box has a mirror finish to minimize the effect of radiant heat, and it has a high-performance insulating foam layer between the box and battery to reduce effect of convection heat. This battery box was engineered to be strong enough to withstand 30 G of force yet only weighs .375Kg or 13.2oz.
All batteries have optimal temperature ranges for use in operation. The ETX-Hundred series is rated for 140 deg F ( 60 deg C) or less for optimal longevity and performance of the battery. Typical lead acid batteries are rated to 113 deg F or 45 deg C.
BB-MU2 Light Weight Aluminum Battery Box
The light weight aluminum battery box is excellent to use with the EarthX lithium “E” case batteries for easy installation. Has a bolt-down tab for easy removal of the battery from the front or top, and is acrobat rated (even with PC680).
This battery box can be used with: ETX680, ETX900, ETX900-VNT, ETX1200, and Odyssey’s PC680
If you are using the battery box for the EarthX Lithium batteries, you will use a foam spacer on the left and right side of the battery for a snug fit. If you are using the battery box for the PC680, you will use the foam spacer on the backside at the bottom of the case to adjust for the tapering of the case for a snug fit.
This battery box was engineered to be strong enough to withstand 30 G of force for the EarthX Lithium Batteries or 6G of upward force and 9G of downward force with the PC680. It only weighs .23Kg or 8oz. This unique design allows for simple, easy installation with the dimensions: 7.1″ L x 3.1″ W x 6.5-6.6″ (adjustable height) or (180mm x 80mm 166-168mm).
What’s included:
- 1 x battery box
- 1 x top front removeable hold down tab
- 2 x screws for hold down
ETX-QCC4 EarthX 48″ Quick Connect Cable
SPECIFICATIONS
- Max jump start amps: 400 amps
- Length: Battery “pigtail” cable = 48”/122 cm
- Jump pack adapter cable: 12”/30 cm
- 1/4″ / M6 ringlets
- Industry standard 2-pole SAE connector, with rubber sealing cap.
- Cable max. rating: 400 Amp
When not in use, keep rubber sealing cap closed on the SAE connector end.
You can then use this pigtail to charge your battery or for jump starting.
If the cables get hot, disconnect and allow them to cool down before use.
Caution: Never use the supplied battery chargers pigtail cables that comes with your charger for jump starting as they are not designed to carry this amount of amperage. Only use the EarthX quick connect (model# ETX-QCC4) cables to jump the battery.
1/4″ Vent Tubing
Tubing for the EarthX ETX900-VNT or the ETX900-TSO vented batteries. Only EarthX approved or supplied tubing should be used. The tubing is chemical resistant and rated for 500°F. Be careful not to crush or restrict flow through the tubing. Enter the quantity you want in feet.
1/4″ inside diameter, 5/16″ outside diameter
