11MM12 12V Military Grade LED Indicator Light (Dimmable And Push-To-Test)
$139.00
Specifications
- Color: Amber
- Voltage: 12V
- Drill bit size: 15/32″
What’s included
- Wire 20ga – 20ft in length
- Mounting: Nut and Washer (included)
- Replaceable LED Lamp
- Fuse Holder with 1 Amp Fuse
LED Press to Test indicator features a dimming actuator, LED replaceable lamp, and an amber lens. Military grade panel mount indicator meets or exceeds military specification MIL-L-3661B with high quality black anodized aluminum housing.
The 12V LED is easy to installation and compatible with a 10-15V electrical system. If you do not have an EFIS to connect to, this is a required indicator light if installing in a certified aircraft along with the ETX900-TSO battery. Detailed installation directions are located in the EarthX manual but it is very simple. To install, connect red wire to a positive bus connection, connect the black wire to fault monitoring wire (also black) that is located on the EarthX battery.
The positive wire (red wire) of the LED should be connected to the electrical bus (12volt positive), typically to a fuse/breaker downstream of the master switch. The negative of the LED (black wire) should be connected to the fault monitor wire (wire out the side of the battery) of the battery.
Step 1: Install the 12V LED light thru a hole in your control panel.
Step 2: Cut the black wire to length desired for your installation so the LED’s black wire reaches the battery.
Step 3: Use a wire stripper to remove ¼” of the wire insulation so you can attach the “male” spade connector to the black wire. Crimp the male spade connector to black wire.
Step 4: Plug the male spade connector into the end of the pigtail wire from the battery.
Step 5: Connect the red wire to an electrical bus fuse/breaker (.25-1 AMP). Most of the time it is most convenient to connect to a fuse on the back side of the panel. If not, it could also be connected directly to the positive terminal of the battery with a ¼” ring lug connector.
Specifications:
- Color: Amber
- Voltage: 12V
- Drill bit size: 15/32″
What’s included:
- Wire 20ga – 20ft in length
- Mounting: Nut and Washer (included)
- Replaceable LED Lamp
- Fuse Holder with 1 Amp Fuse
| Weight | 0.1 lbs |
|---|---|
| Dimensions | 0.1 × 0.1 × 0.1 in |
| Brand | EarthX Batteries |
You must be logged in to post a review.
SHIPPING INFORMATION
We can ship by UPS, or USPS and DHL Express. We ship nationally, and internationally.
Carriers In Use
SHIPPING COSTS
- International Shipping Quote has to be done manually due to dimensions, weight, end destination, and more. Please E-Mail us.
- Any manner or method is available, call if you need Priority 1-2 day or overnight shipping.
- We are shipping with UPS or USPS and DHL Express
Related products
BB-TH-U Thermal Battery Box “U” Case
Thermal battery box to protect from radiated or convection heat. This battery box is designed to be compatible with our existing “U” case battery models; ETX1600, ETX900-24, ETX680-24-VNT.
The EarthX thermal battery box is designed to protect the battery in engine compartment installations from periods of high temperature (up to 1 hour), such as after shutdown, and from radiant heat from hot surfaces like exhaust systems during and after flight. This stainless-steel box has a mirror finish to minimize the effect of radiant heat, and it has a high-performance insulating foam layer between the box and battery to reduce effect of convection heat. Weight is .68Kg or 1 Lb. 8oz.
All batteries have optimal temperature ranges for use in operation. The ETX-Hundred series is rated for 140 deg F (60 deg C) or less for optimal longevity and performance of the battery. Typical lead acid batteries are rated to 113 deg F or 45 deg C.
BB-U Light Weight Aluminum Battery Box For “U” Case
This is a custom fit designed battery box for the ETX1600, the ETX900-24, or the ETX680-24-VNT battery. This battery box has a removable hold down bracket which allows the battery to be removed from the top or the front for easy installation and use. It is made of aluminum weighing only .325Kg or 11.5oz, yet can handle 9Gs force downward and 6Gs upward.
What’s included:
- 1 x battery box
- 1 x top front removable hold down tab
- 2 x screws for hold down
BB-MU2 Light Weight Aluminum Battery Box
The light weight aluminum battery box is excellent to use with the EarthX lithium “E” case batteries for easy installation. Has a bolt-down tab for easy removal of the battery from the front or top, and is acrobat rated (even with PC680).
This battery box can be used with: ETX680, ETX900, ETX900-VNT, ETX1200, and Odyssey’s PC680
If you are using the battery box for the EarthX Lithium batteries, you will use a foam spacer on the left and right side of the battery for a snug fit. If you are using the battery box for the PC680, you will use the foam spacer on the backside at the bottom of the case to adjust for the tapering of the case for a snug fit.
This battery box was engineered to be strong enough to withstand 30 G of force for the EarthX Lithium Batteries or 6G of upward force and 9G of downward force with the PC680. It only weighs .23Kg or 8oz. This unique design allows for simple, easy installation with the dimensions: 7.1″ L x 3.1″ W x 6.5-6.6″ (adjustable height) or (180mm x 80mm 166-168mm).
What’s included:
- 1 x battery box
- 1 x top front removeable hold down tab
- 2 x screws for hold down
Reviews
There are no reviews yet.