Optimate TM-275 v2 10 amp Battery Charger/Maintainer/Power Supply (12-13.2V Batteries)
$219.95
This Optimate Lithium charger will quickly charge your battery at 10 amps, maintain it at the optimal voltage, and can be used as a power source of 8 continuous amps! For example, you can use it as power supply while programming your aircraft EFIS so you are not draining your battery while you work.
This Optimate Lithium charger will quickly charge your battery at 10 amps, maintain it at the optimal voltage, and can be used as a power source of 8 continuous amps! For example, you can use it as power supply while programming your aircraft EFIS so you are not draining your battery while you work.
Features:
- CHARGER
- MAINTAINER
- POWER SUPPLY (8 amps at 13.6V by pressing TUNE Button)
What’s included:
- 1 x TM-275 v2 charger/maintainer/power supply
- 1 x battery alligator clips
- 1 x waterproof quick connect lead with ringlets and SAE connector
High efficiency diagnostic Optimate lithium battery charger and tester for LiFePO4 / LFP batteries.
Perfect for charging of a high performance 12.8V-13.2V LiFePO4 / LFP battery sized from 2.5 to 120 Amp-hour.
Special features:
- TUNE mode delivers stable power for vehicle system reprogramming, show room vehicle demo or retaining memorized settings when battery cables are disconnected to fit powered accessories or replace the battery.
- BMS reset, pushbutton activated – for batteries with resettable low voltage / deep discharge protection.
- Battery SAVE mode with BMS reset : starts from 0.5V with continuous monitoring / testing of charge acceptance or bad / shorted cell condition. Unnecessary (and unsafe) charging of a bad battery is prevented.
- safeTº : Automatic charge rate adjustment to ambient temperature sensed at the charger. Reduced charging below freezing, no charging if temperature is below -20ºC/-4ºF (can damage lithium batteries).
- Ampmatic : Microprocessor adjusts current to ideal LiFePO4 charge curve to match battery size / condition, for fastest and most complete charge.
SAVE : Low Volt Start of 0.5V + 3-step low volt SAVE and TEST
Technical Specifications of Optimate lithium battery charger:
- Recommended for LiFePO4 batteries: up to 120Ah
- Operation: Fully automatic
- Charging amps: 9.5
- Charging volts: 12.8V (nominal) 0.5V – 14.4V (range)
- Charge time limit: 24 hours (maintenance time: unlimited)
- Maintain/test cycles: 30 min/30 min (alternating hourly)
- Safe: No risk of overcharging. Totally safe for vehicle electronics. Sparks suppressed. Safe for long-term battery maintenance. Automatic shut-down if short-circuited or battery disconnected
- Style: Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector
- Operation temperature range: -40°C – +40°C
- Warranty: 3 years
Charging Versatility With EarthX Batteries
EarthX Batteries use an intelligent Battery Management System (BMS) to balance the batteries as they charge. This capability is a major benefit to users because a specialty charger isn’t required for your EarthX Batteries to perform.
The BMS uses a microprocessor that monitors the cells to keep them in an optimal state to insure performance and longevity. The system also protects the battery as it functions. With the BMS, charging practices are important but not critical to battery performance. The BMS handles many of the complexities of charging, so you don’t have to.
With the BMS ensuring balance, you can enjoy more flexibility in battery usage. Additionally, EarthX Batteries offer high discharge capacities and fast charging speeds.
Recommended Lithium Battery Chargers
As the owner of a lithium iron phosphate (LFP) battery from EarthX, you may want to invest in a dedicated charger directly from our site. We offer several chargers for EarthX Batteries. Products we carry include:
- Optimate TM-281 5 Amp Battery Charger/Maintainer/Power Supply (24-28V batteries) – EarthX Batteries: To charge 24- to 28-volt lithium batteries, use this charger. With a “tune” feature that is a power source with 4 continuous amps of energy while you program your electronic flight instrument system or retune your car.
- Optimate TM-391 6 Amp Battery Charger/Maintainer/Power Supply(12-13.2V Batteries) – EarthX Batteries: This charger provides 6 amps of charging energy, 5 amps continuous as a power supply or can also be used as a maintainer to keep your battery ready when you are. It has a weatherproof case for indoor and outdoor use.
- Optimate TM-275 10 Amp Battery Charger/Maintainer/Power Supply (12-13.2V Batteries) – EarthX Batteries Optimate TM-275 10 Amp Battery Charger/Maintainer/Power Supply (12-13.2V Batteries): Charge your battery at 10 amps. Also, use it as a 8 amp power source to save your battery for applications like programming an aircraft, or leave it connected to keep you battery topped off and ready as a maintainer.
Best Lithium Battery Charging Practices
All batteries wear down over time and lose capacity and cranking abilities. Both scenarios mean the battery will be less powerful over time. To maintain battery performance and extend it’s life, follow these charging practices:
- Follow minimum voltage requirements and keep batteries charged at this value or higher.
- Use a plug-in charger over a jump start whenever possible.
- Avoid leaving your battery discharged for any period of time.
Buy An EarthX-Recommended Battery Charger
If you need a power source for your lithium batteries, EarthX has several charging options for 12- to 28-volt batteries.
| Weight | 0.1 lbs |
|---|---|
| Dimensions | 0.1 × 0.1 × 0.1 in |
| Brand | EarthX Batteries |
You must be logged in to post a review.
SHIPPING INFORMATION
We can ship by UPS, or USPS and DHL Express. We ship nationally, and internationally.
Carriers In Use
SHIPPING COSTS
- International Shipping Quote has to be done manually due to dimensions, weight, end destination, and more. Please E-Mail us.
- Any manner or method is available, call if you need Priority 1-2 day or overnight shipping.
- We are shipping with UPS or USPS and DHL Express
Related products
ETX900-TSO-35-PA-KIT
STC installation kit to be used with the ETX900-TSO. Use for replacing a Concorde or Gill 35 Ah battery.
We are adding kits for many other make/models. Please check back regularly.
ETX-JMP12/24 12V-24V Jump Pack (All-In-One)
This is a 12V/24V jump pack that can boost just about anything! Very compact and the entire kit is only 4 pounds. This jump pack uses the technology of lithium iron phosphate (LiFePo4) chemistry, not Lithium Cobalt (LiCoO2). LiFePo4 is the most powerful, safest and most robust of all the lithium chemistries, plus double the life span of lithium cobalt packs.
Examples of what it can jump start: automobiles, diesel trucks, motorcycles, boats, construction equipment, experimental and certified aircraft, tractors, snowmobiles, ATV/UTVs, riding lawnmowers, and so much more.
ETX900-TSO-35-KIT
What’s included:
- 1 x Panel mount LED (11MM12)
- 1 x Battery Box Spacer (190531)
- 1 x Fault Indicator Placard (200208)
- 1 x 3/8″ Tubing (5239K15)
- 1 x 1/4″ Tubing (5239K13)
- 1 x 3/8″ Wye Tube Fitting (5463K722)
- 3/8″ ID 9/16″ OD Grommets (9600K86)
BB-MU2 Light Weight Aluminum Battery Box
The light weight aluminum battery box is excellent to use with the EarthX lithium “E” case batteries for easy installation. Has a bolt-down tab for easy removal of the battery from the front or top, and is acrobat rated (even with PC680).
This battery box can be used with: ETX680, ETX900, ETX900-VNT, ETX1200, and Odyssey’s PC680
If you are using the battery box for the EarthX Lithium batteries, you will use a foam spacer on the left and right side of the battery for a snug fit. If you are using the battery box for the PC680, you will use the foam spacer on the backside at the bottom of the case to adjust for the tapering of the case for a snug fit.
This battery box was engineered to be strong enough to withstand 30 G of force for the EarthX Lithium Batteries or 6G of upward force and 9G of downward force with the PC680. It only weighs .23Kg or 8oz. This unique design allows for simple, easy installation with the dimensions: 7.1″ L x 3.1″ W x 6.5-6.6″ (adjustable height) or (180mm x 80mm 166-168mm).
What’s included:
- 1 x battery box
- 1 x top front removeable hold down tab
- 2 x screws for hold down
211215 G35 Mooney Custom Molded Foam Insert
Vent Port Kit
This kit includes includes machined aluminum vent port, washer and nut to make the installation of a vented EarthX battery easy and professional looking. This vent port is designed for our ETX900-VNT battery. This custom machined port is designed to accept the ETX900’s ¼” O.D. vent tubes. The port is an anodized aircraft aluminum. The two vent tubes easily connect to the port with a “push-to-connect” connection like most small diameter tube fittings on the market today.
This port can be incorporated into most new or existing aircraft builds, making a clean, low profile finish.
Hole size required in aircraft skin for port is 1 1/8”.
ETX-QCC4 EarthX 48″ Quick Connect Cable
SPECIFICATIONS
- Max jump start amps: 400 amps
- Length: Battery “pigtail” cable = 48”/122 cm
- Jump pack adapter cable: 12”/30 cm
- 1/4″ / M6 ringlets
- Industry standard 2-pole SAE connector, with rubber sealing cap.
- Cable max. rating: 400 Amp
When not in use, keep rubber sealing cap closed on the SAE connector end.
You can then use this pigtail to charge your battery or for jump starting.
If the cables get hot, disconnect and allow them to cool down before use.
Caution: Never use the supplied battery chargers pigtail cables that comes with your charger for jump starting as they are not designed to carry this amount of amperage. Only use the EarthX quick connect (model# ETX-QCC4) cables to jump the battery.



Reviews
There are no reviews yet.