Fuel Quantity Adapter Cable Module | DC400A or DC400 Test Set, Bell 412SP, Bell 412HP
Contact Cost Aero at 855-500-3044 for pricing
The 101-00807 Fuel Quantity Adapter Cable Module is compatible with DC400A test sets for the Bell 412SP and Bell 412HP helicopters with serial numbers 108 and on.
Features
Features:
- For use with DC400A test set
Compatible aircraft:
- Bell 412SP
- Bell 412HP
| Brand | Barfield |
|---|
You must be logged in to post a review.
SHIPPING INFORMATION
We can ship by UPS, or USPS and DHL Express. We ship nationally, and internationally. Â
Carriers In Use
SHIPPING COSTS
- International Shipping Quote has to be done manually due to dimensions, weight, end destination, and more.  Please E-Mail us.
- Any manner or method is available, call if you need Priority 1-2 day or overnight shipping.
- We are shipping with UPS or USPS and DHL Express
Related products
A200-PSF Fuel Pressure Sensor
The A200-PSF is a bulk micro-machined, gage type pressure sensor for use in both harsh and benign media with superior accuracy over an operating temperature of -40°C to 105°C. It has superb accuracy of +/- 0.5% full scale.
It contains a custom ASIC which provides signal conditioning for calibration and temperature compensation at the point of measurement. Each sensor is traceable to NIST calibration standards.
Power requirements are 5V / 10mA. Signal output is linear and varies from 0.5V (0 PSI) to 4.5V (100 PSI). Overpressure burst rating is 300 PSI.
The sensor has a 1/8" NPT threaded port for connection to the fuel pressure line.
Supplied with a 36" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this pressure sensor is STC'd as a primary replacement.
A200-HMS – Slick/Unison Rotational Speed Sensor
The A200-HMS is an Hall Effect rotational speed sensor. It provides a speed accuracy of 1 RPM when used in conjunction with the TM200 instrument.
The output signal is a latched, pulse width modulated square wave output of 0V to a maximum of 30V, proportional to rotational speed.
Power requirements are 3.8V to 30V / 3mA.
Precision machined from 6061 T6 aircraft grade aluminum, this sensor is designed to thread into the vent hole of Slick/Unison unpressurized magnetos.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this speed sensor is STC'd as a primary replacement.
A200-HAS Hall Effect Current Shunt
The A200-HAS is an economical and precise solution for DC current measurement in electrical systems up to +/- 100A in capacity.
The output of the device has a positive slope (Vcc / 2) when an increasing current flows through the primary copper conduction path. The internal resistance of this conductive path is 130 µΩ typical, providing low power loss.
The thickness of the copper conductor allows survival of the device at up to 5× overcurrent conditions. The terminals of the conductive path are electrically isolated from the sensor leads and provide a minimum isolation of 3,000V.
Current sense response time is 3uS.
Power requirements are 3V @ 10mA. Signal output is linear and varies from 0.0V (-100A) to 3.0V (+100). Zero current is represented by 1.5V.
The sensor has two 1/4" terminal posts for connection to the power bus.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this current sense shunt is STC'd as a primary replacement.
A200-TEC15 EGT Probe Kit
The A200-TEC15 is a Type-K ungrounded, fast response EGT thermocouple probe kit that will fit an exhaust with an outside diameter of 1 1/4" to 1 3/4". Each probe kit includes:
- One EGT probe with 4' twisted shielded leads and male shielded thermocouple connector.
- One 1 1/2" aircraft grade 316 stainless steel ring clamp.
- One Female polarized and shielded connector for connection to instrument harness.
A200-TEC25 EGT Probe Kit
The A200-TEC25 is a Type-K ungrounded, fast response EGT thermocouple probe kit that will fit an exhaust with an outside diameter of 1 5/8" to 2 1/2". This probe will fit most Continental and Lycoming installations. Each probe kit includes:
- One EGT probe with 4' twisted shielded leads and male shielded thermocouple connector.
- One 2 1/2" aircraft grade 316 stainless steel ring clamp.
- One Female polarized and shielded connector for connection to instrument harness.
Instrument Intensity Potentiometer – Rev 02
Instrument Intensity Potentiometer - Rev 2 - 5 Instruments ONLY
NOTE: This item is only required for use on products purchased on or AFTER 03-JAN-2013.
This potentiometer will support up to ten instruments in a single installation. It provides infinitely variable, uniform intensity control for all instruments.
These units are TSO qualified with all 200 Series instruments and is STC'd as a primary replacement instrument component under all flight conditions (day/night VFR and IFR).
Reviews
There are no reviews yet.