Category – Avionics – Accessories
Stratus Audio Cable
Dual Digital USB Charger
As pilots know, not just any charger will work in an airplane. MyGoFlight developed the first charger for use in aviation which was incredibly successful. To raise the bar, we have now created the Dual Digital with a display that shows volts in and amps drawn by each port. No guessing! Further, it supports USB A & USB C and carries 36W of quick charging power - enough to charge the iPad 11 while in use!
MY-CO Carbon Monoxide Detector | USB Powered
6430202-20 High Power USB Charger
Model Number: TA202
Technical Description
15W/3A out per port, 10–32 VDC in, Single USB-A, Bottom connector, Lighted
Select options
This product has multiple variants. The options may be chosen on the product page
6430360-13 MAX Power USB Charger
Model Number: TA360-CCL
Technical Description
60W/3A out per port, 22–32 VDC in, Dual USB-C PD, Rear connector, Lighted
Select options
This product has multiple variants. The options may be chosen on the product page
A200-TEC20 EGT Probe Kit
The A200-TEC20 is a Type-K ungrounded, fast response EGT thermocouple probe kit that will fit an exhaust with an outside diameter of 1 1/2" to 2". Each probe kit includes:
- One EGT probe with 4' twisted shielded leads and male shielded thermocouple connector.
- One 2" aircraft grade 316 stainless steel ring clamp.
- One Female polarized and shielded connector for connection to instrument harness.
A200-TEC15 EGT Probe Kit
The A200-TEC15 is a Type-K ungrounded, fast response EGT thermocouple probe kit that will fit an exhaust with an outside diameter of 1 1/4" to 1 3/4". Each probe kit includes:
- One EGT probe with 4' twisted shielded leads and male shielded thermocouple connector.
- One 1 1/2" aircraft grade 316 stainless steel ring clamp.
- One Female polarized and shielded connector for connection to instrument harness.
A200-HMB – Bendix Rotational Speed Sensor
The A200-HMB is an Hall Effect rotational speed sensor. It provides a speed accuracy of 1 RPM when used in conjunction with the TM200 instrument.
The output signal is a latched, pulse width modulated square wave output of 0V to a maximum of 30V, proportional to rotational speed.
Power requirements are 3.8V to 30V / 3mA.
Precision machined from 6061 T6 aircraft grade aluminum, this sensor is designed to thread into the vent hole of Bendix unpressurized magnetos.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this speed sensor is STC'd as a primary replacement.
P-300M Magnetic Float Sensor
PT-100GA – Pressure Transducer
Fuel Flow Transducer 201B
The Fuel Flow Transducer measures flows of hydrocarbon fuels such as gasoline, kerosene, and #2 diesel fuel and other light transmitting, non-corrosive liquids of similar viscosity. Typical fuel flow applications include aircraft fuel monitoring systems; gasoline, diesel, and gas turbine engine test stands; and industrial furnaces.
The transducers give repeatable signals on gasoline across a 100 to 1 flow range down to 0.3 GPH. The higher viscosity of diesel fuel reduces signal repeatability at flow rates below 2 GPH. Pressure drops are very low compared to other turbine flow transducers. The transducer bearing system is rated for continuous operation at the upper end of the flow range.
The transducers produce a current pulse signal from an opto-electronic pickup with a preamplifier.
Fuel Flow Transducer 231
The Fuel Flow Transducer measures flows of hydrocarbon fuels such as gasoline, kerosene, and #2 diesel fuel and other light transmitting, non-corrosive liquids of similar viscosity. Typical fuel flow applications include aircraft fuel monitoring systems; gasoline, diesel, and gas turbine engine test stands; and industrial furnaces.
The transducers give repeatable signals on gasoline across a 100 to 1 flow range down to 0.3 GPH. The higher viscosity of diesel fuel reduces signal repeatability at flow rates below 2 GPH. Pressure drops are very low compared to other turbine flow transducers. The transducer bearing system is rated for continuous operation at the upper end of the flow range.
The transducers produce a current pulse signal from an opto-electronic pickup with a preamplifier.
