Category – Avionics – Accessories
A200-PSO Oil Pressure Sensor
The A200-PSO is a bulk micro-machined, gage type pressure sensor for use in both harsh and benign media with superior accuracy over an operating temperature of -40°C to 105°C. It has superb accuracy of +/- 0.5% full scale.
It contains a custom ASIC which provides signal conditioning for calibration and temperature compensation at the point of measurement. Each sensor is traceable to NIST calibration standards.
Power requirements are 5V / 10mA. Signal output is linear and varies from 0.5V (0 PSI) to 4.5V (200 PSI). Overpressure burst rating is 600 PSI.
The sensor has a 1/8" NPT threaded port for connection to the oil pressure line.
Supplied with a 36" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this pressure sensor is STC'd as a primary replacement.
A200-HMS – Slick/Unison Rotational Speed Sensor
The A200-HMS is an Hall Effect rotational speed sensor. It provides a speed accuracy of 1 RPM when used in conjunction with the TM200 instrument.
The output signal is a latched, pulse width modulated square wave output of 0V to a maximum of 30V, proportional to rotational speed.
Power requirements are 3.8V to 30V / 3mA.
Precision machined from 6061 T6 aircraft grade aluminum, this sensor is designed to thread into the vent hole of Slick/Unison unpressurized magnetos.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this speed sensor is STC'd as a primary replacement.
A200-HAS Hall Effect Current Shunt
The A200-HAS is an economical and precise solution for DC current measurement in electrical systems up to +/- 100A in capacity.
The output of the device has a positive slope (Vcc / 2) when an increasing current flows through the primary copper conduction path. The internal resistance of this conductive path is 130 µΩ typical, providing low power loss.
The thickness of the copper conductor allows survival of the device at up to 5× overcurrent conditions. The terminals of the conductive path are electrically isolated from the sensor leads and provide a minimum isolation of 3,000V.
Current sense response time is 3uS.
Power requirements are 3V @ 10mA. Signal output is linear and varies from 0.0V (-100A) to 3.0V (+100). Zero current is represented by 1.5V.
The sensor has two 1/4" terminal posts for connection to the power bus.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this current sense shunt is STC'd as a primary replacement.
FT-90 Fuel Flow Transducer
PT-300GA – Pressure Transducer
P-128 – OAT/Carb Temp Probe
P-110-F EGT Fast Response Probe
P-120 – Oil Temp Probe
CP-1A – LED Intensity Control Pot
Fuel Flow Transducer 231
The Fuel Flow Transducer measures flows of hydrocarbon fuels such as gasoline, kerosene, and #2 diesel fuel and other light transmitting, non-corrosive liquids of similar viscosity. Typical fuel flow applications include aircraft fuel monitoring systems; gasoline, diesel, and gas turbine engine test stands; and industrial furnaces.
The transducers give repeatable signals on gasoline across a 100 to 1 flow range down to 0.3 GPH. The higher viscosity of diesel fuel reduces signal repeatability at flow rates below 2 GPH. Pressure drops are very low compared to other turbine flow transducers. The transducer bearing system is rated for continuous operation at the upper end of the flow range.
The transducers produce a current pulse signal from an opto-electronic pickup with a preamplifier.
RPM Sensor for Slick Mag
Please review the 3 choices below for the correct sensor. When ordering use the drop down option box, if necessary.
- Slick Non press PN- 420815-1 $299
- Slick 600 (press or non press) PN-420806 $395
- Slick 6000 420809 $395
Select options
This product has multiple variants. The options may be chosen on the product page
TA14 Transponder Antenna
Control Valve Servo Kit
Control Valve Servo Kit (CVS) is a system for controlling valves and dampers and is ideal for heater flapper doors, oil cooler control, alternate air door, and ventilation dampers. The CVS kit includes an instrument panel mounted controller, linear actuator servo and a pre-made 5-foot wiring harness.
CVS is available in four different models: 12-volt standard (30 mm travel linear actuator servo), 12-volt heavy-duty (50 mm travel linear actuator servo), 24-volt standard (30 mm travel linear actuator servo) and 24-volt heavy-duty (50 mm travel linear actuator servo).
Select options
This product has multiple variants. The options may be chosen on the product page
IBBS Replacement Batteries (3ah and 6ah)
LiFe battery pack replacement for the Integrated Battery Back-up System. IBBS replacement batteries are available for all Experimental and Certified IBBS models.
Select options
This product has multiple variants. The options may be chosen on the product page
External GPS Antenna for EKPV
