Showing 37–48 of 114 results

PT-30GA – Pressure Transducer

$228.00
PT-30GA – Pressure Transducer FAA Approved Instrument FAA TSO’d, STC’d, PMA’d Accurate and stable, precise pressure measurements. Robust Construction, stainless

PT-100GA – Pressure Transducer

$228.00
PT-100GA – Pressure Transducer FAA Approved Instrument FAA TSO’d, STC’d, PMA’d Accurate and stable, precise pressure measurements. Robust Construction, stainless

IBBS Replacement Batteries (3ah and 6ah)

$105.00$220.00
LiFe battery pack replacement for the Integrated Battery Back-up System. IBBS replacement batteries are available for all Experimental and Certified IBBS models.

A200-TSO Oil Temperature Sensor

$218.00
The A200-TSO is a monolithic temperature sensor with on-chip signal conditioning and an operating temperature of -50°C to 150°C. It has an accuracy of +/- 0.5°C over the full operating range. The output voltage is proportional to the temperature x the supply voltage (ratiometric). The output swings from 0.25 V at −50°C to +4.75 V at +150°C using a single +5.0 V supply. The temperature transfer function is: VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA] Power requirements (when used with any 200 Series instrument) are 5V / 1mA. The sensor has a 5/8-18 threaded body and includes a copper crush washer. Supplied with a 48" color coded cable. When installed in accordance with the approved instructions and as part of a qualified instrument system, this temperature sensor is STC'd as a primary replacement.

AOG FEE Aerospace Logic

$200.00
AOG FEE Aerospace Logic   For the fastest turn around time, choose an AOG FEE, and next day shipping on

A200-TSA Outside Air Temperature Sensor

$199.00
The A200-TSA is a monolithic temperature sensor with on-chip signal conditioning and an operating temperature of -50°C to 150°C. It has an accuracy of +/- 0.5°C over the full operating range. The output voltage is proportional to the temperature x the supply voltage (ratiometric). The output swings from 0.25 V at −50°C to +4.75 V at +150°C using a single +5.0 V supply. The temperature transfer function is: VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA] Power requirements are 5V / 1mA. The sensor has a 5/16-24 threaded body and is supplied with two nylon mounting washers and a Nyloc fastening nut. Supplied with a 48" color coded cable. When installed in accordance with the approved instructions and as part of a qualified instrument system, this temperature sensor is STC'd as a primary replacement.

A200-HAS Hall Effect Current Shunt

$198.00
The A200-HAS is an economical and precise solution for DC current measurement in electrical systems up to +/- 100A in capacity. The output of the device has a positive slope (Vcc / 2) when an increasing current flows through the primary copper conduction path. The internal resistance of this conductive path is 130 µΩ typical, providing low power loss. The thickness of the copper conductor allows survival of the device at up to 5× overcurrent conditions. The terminals of the conductive path are electrically isolated from the sensor leads and provide a minimum isolation of 3,000V. Current sense response time is 3uS. Power requirements are 3V @ 10mA. Signal output is linear and varies from 0.0V (-100A) to 3.0V (+100). Zero current is represented by 1.5V. The sensor has two 1/4" terminal posts for connection to the power bus. Supplied with a 48" color coded cable. When installed in accordance with the approved instructions and as part of a qualified instrument system, this current sense shunt is STC'd as a primary replacement.

Oil Temp Probe

$195.00
The OIL Temperature (OIL) probe is for all Lycoming and Continental direct drive engines and is installed in the right (passenger) side front OIL galley by removing the existing 1/8 NPT plug. The probe has a 3/8-24 boss which will fit the factory pre-drilled hole for this probe.
  • 1 Thermocouple Type K OIL Temperature Probe
  • 1-10 Ft. Option Wire

OAT Probe

$195.00
The Outside Air Temperature (OAT) probe has an outside aluminum shield which is used to both hold the probe in place and shield it from radiated heat. When installing the OAT probe, shield the sensor from direct sunlight and engine heat. The OAT probe is installed in the airframe manufactures recommended location, if this information is not available, we recommend installing the probe in clean airflow such as in a cabin air scoop or below the underside of the wing away from engine heat or exhaust heat.
  • 1 Thermocouple Type K OAT Probe
  • 1-10 Ft. Option Wire

CRB Probe

$195.00
The Carburetor Temperature Probe (CRB) probe, is installed in the Carburetor throat. A pre-drilled 1/8 NPT port is available from

TIT Probe

$195.00
The Turbine Inlet temperature (TIT) probe, is installed in the exhaust stack accumulator to a maximum depth of 1/2 inches and approximately 2-4 inches from the turbine inlet, on the wastegate side of the turbine. The TIT probe is shipped with a #48 stainless steel clamp.

TIT 7/16-20 Screw in Type Probe

$195.00
The Turbine Inlet temperature (TIT) probe,  Screw-in type with 7/16-20 thread. Shipped as kit ready to install.