W31 Series Circuit Breaker | 7.5 Amp Rating, Toggle Actuator
$72.66
A tariff fee of $6.6222 EA may apply
The W31 series are single pole, thermal circuit breakers with toggle actuator and series trip function. They are UL 1077 Recognized as Supplementary Protectors. File E69543, and CSA Accepted as Supplementary Protectors (Appliance Component Protectors), File LR15734.
Includes hardware.
Features
The W31-X2M1G-7.5 circuit breaker is rated for 7.5 amps.
- 0.5 amp to 50 amp ratings may be used as on/off switch
- Cannot be reset against overload
- Screw termination
- Trip-free operation
- Silver with amp rate marking toggle switch
- Two hex nuts/lockwasher installed mounting hardware
Specifications
Weight:
Less than 2 oz
Mounting:
Panel mount
15/32 in threaded bushing .320 in (8.13mm) long, double “D”, silver color
Terminals:
Two #8-32 screw terminals (90° to each other termination)
Dielectric Strength:
Over 1,500 volts RMS
Maximum Operating Voltages:
50VDC or 240VAC (to 400 Hz)
Current Rating:
7.5 amp
Voltage Rating AC:
250 VAC
Voltage Rating DC:
50 VDC
| Weight | .1 lbs |
|---|---|
| Dimensions | 10 × 8 × 6 in |
| Brand | TE Connectivity |
You must be logged in to post a review.
SHIPPING INFORMATION
We can ship by UPS, or USPS and DHL Express. We ship nationally, and internationally.
Carriers In Use
SHIPPING COSTS
- International Shipping Quote has to be done manually due to dimensions, weight, end destination, and more. Please E-Mail us.
- Any manner or method is available, call if you need Priority 1-2 day or overnight shipping.
- We are shipping with UPS or USPS and DHL Express
Related products
A200-PMP Manifold Pressure Sensor
The A200-PMP is a bulk micro-machined, absolute type pressure sensor for use in both harsh and benign media with superior accuracy over an operating temperature of -40°C to 105°C. It has superb accuracy of +/- 0.5% full scale.
It contains a custom ASIC which provides signal conditioning for calibration and temperature compensation at the point of measurement. Each sensor is traceable to NIST calibration standards.
Power requirements are 5V / 10mA. Signal output is linear and varies from 0.5V (0 PSI) to 4.5V (50 PSI). Overpressure burst rating is 300 PSI.
The sensor has a 1/8" NPT threaded port for connection to the manifold pressure line.
Supplied with a 36" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this pressure sensor is STC'd as a primary replacement.
A200-TSO Oil Temperature Sensor
The A200-TSO is a monolithic temperature sensor with on-chip signal conditioning and an operating temperature of -50°C to 150°C. It has an accuracy of +/- 0.5°C over the full operating range.
The output voltage is proportional to the temperature x the supply voltage (ratiometric). The output swings from 0.25 V at −50°C to +4.75 V at +150°C using a single +5.0 V supply.
The temperature transfer function is:
VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA]
Power requirements (when used with any 200 Series instrument) are 5V / 1mA.
The sensor has a 5/8-18 threaded body and includes a copper crush washer.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this temperature sensor is STC'd as a primary replacement.
A200-TEC25 EGT Probe Kit
The A200-TEC25 is a Type-K ungrounded, fast response EGT thermocouple probe kit that will fit an exhaust with an outside diameter of 1 5/8" to 2 1/2". This probe will fit most Continental and Lycoming installations. Each probe kit includes:
- One EGT probe with 4' twisted shielded leads and male shielded thermocouple connector.
- One 2 1/2" aircraft grade 316 stainless steel ring clamp.
- One Female polarized and shielded connector for connection to instrument harness.
A200-PSF Fuel Pressure Sensor
The A200-PSF is a bulk micro-machined, gage type pressure sensor for use in both harsh and benign media with superior accuracy over an operating temperature of -40°C to 105°C. It has superb accuracy of +/- 0.5% full scale.
It contains a custom ASIC which provides signal conditioning for calibration and temperature compensation at the point of measurement. Each sensor is traceable to NIST calibration standards.
Power requirements are 5V / 10mA. Signal output is linear and varies from 0.5V (0 PSI) to 4.5V (100 PSI). Overpressure burst rating is 300 PSI.
The sensor has a 1/8" NPT threaded port for connection to the fuel pressure line.
Supplied with a 36" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this pressure sensor is STC'd as a primary replacement.
Instrument Intensity Potentiometer – Rev 02
Instrument Intensity Potentiometer - Rev 2 - 5 Instruments ONLY
NOTE: This item is only required for use on products purchased on or AFTER 03-JAN-2013.
This potentiometer will support up to ten instruments in a single installation. It provides infinitely variable, uniform intensity control for all instruments.
These units are TSO qualified with all 200 Series instruments and is STC'd as a primary replacement instrument component under all flight conditions (day/night VFR and IFR).
Reviews
There are no reviews yet.