W31 Series Circuit Breaker | 50 Amp Rating, Toggle Actuator
$70.98
A tariff fee of $11.0160 EA may apply
The W31 series are single pole, thermal circuit breakers with toggle actuator and series trip function. They are UL 1077 Recognized as Supplementary Protectors. File E69543, and CSA Accepted as Supplementary Protectors (Appliance Component Protectors), File LR15734.
Includes hardware.
Features
The W31-X2M1G-50 circuit breaker is rated for 50 amps.
- 0.5 amp to 50 amp ratings may be used as on/off switch
- Cannot be reset against overload
- Screw termination
- Trip-free operation
- Silver with amp rate marking toggle switch
- Two hex nuts/lockwasher installed mounting hardware
Specifications
Weight:
Less than 2 oz
Mounting:
Panel mount
15/32 in threaded bushing .320 in (8.13mm) long, double “D”, silver color
Terminals:
Two #8-32 screw terminals (90° to each other termination)
Dielectric Strength:
Over 1,500 volts RMS
Maximum Operating Voltages:
50VDC or 240VAC (to 400 Hz)
Current Rating:
50 amp
Voltage Rating AC:
240 VAC
Voltage Rating DC:
50 VDC
| Weight | .1 lbs |
|---|---|
| Dimensions | 10 × 8 × 6 in |
| Brand | TE Connectivity |
You must be logged in to post a review.
SHIPPING INFORMATION
We can ship by UPS, or USPS and DHL Express. We ship nationally, and internationally.
Carriers In Use
SHIPPING COSTS
- International Shipping Quote has to be done manually due to dimensions, weight, end destination, and more. Please E-Mail us.
- Any manner or method is available, call if you need Priority 1-2 day or overnight shipping.
- We are shipping with UPS or USPS and DHL Express
Related products
A200-TSO Oil Temperature Sensor
The A200-TSO is a monolithic temperature sensor with on-chip signal conditioning and an operating temperature of -50°C to 150°C. It has an accuracy of +/- 0.5°C over the full operating range.
The output voltage is proportional to the temperature x the supply voltage (ratiometric). The output swings from 0.25 V at −50°C to +4.75 V at +150°C using a single +5.0 V supply.
The temperature transfer function is:
VOUT = (V+/5 V) × [1.375 V +(22.5 mV/°C) × TA]
Power requirements (when used with any 200 Series instrument) are 5V / 1mA.
The sensor has a 5/8-18 threaded body and includes a copper crush washer.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this temperature sensor is STC'd as a primary replacement.
A200-HAS Hall Effect Current Shunt
The A200-HAS is an economical and precise solution for DC current measurement in electrical systems up to +/- 100A in capacity.
The output of the device has a positive slope (Vcc / 2) when an increasing current flows through the primary copper conduction path. The internal resistance of this conductive path is 130 µΩ typical, providing low power loss.
The thickness of the copper conductor allows survival of the device at up to 5× overcurrent conditions. The terminals of the conductive path are electrically isolated from the sensor leads and provide a minimum isolation of 3,000V.
Current sense response time is 3uS.
Power requirements are 3V @ 10mA. Signal output is linear and varies from 0.0V (-100A) to 3.0V (+100). Zero current is represented by 1.5V.
The sensor has two 1/4" terminal posts for connection to the power bus.
Supplied with a 48" color coded cable.
When installed in accordance with the approved instructions and as part of a qualified instrument system, this current sense shunt is STC'd as a primary replacement.
A200-TEC20 EGT Probe Kit
The A200-TEC20 is a Type-K ungrounded, fast response EGT thermocouple probe kit that will fit an exhaust with an outside diameter of 1 1/2" to 2". Each probe kit includes:
- One EGT probe with 4' twisted shielded leads and male shielded thermocouple connector.
- One 2" aircraft grade 316 stainless steel ring clamp.
- One Female polarized and shielded connector for connection to instrument harness.
Reviews
There are no reviews yet.