Category – Avionics – Antennas
CI 1125 VOR GS DUAL DIPLEXER/BNC Female Connector, 108-118 MHz and 329-335 MHz, 50 Ohms, 2 Hole Mount & a Aluminum Finish.
CI 271 UHF ANTENNA/BNC Female Connector, 400-430 MHz, 50 Ohms, 50 Watts, Airspeed 250 Knots
CI-502 Antenna Coupler | Dual VOR, BNC
RAMI AV-12 VOR/LOC/GS Receive Only Antenna
The AV-12 is a VOR/LOC/GS receive only antenna which uses a highly efficient technique of molding the elements directly into a high-impact thermo-setting bakelite center insulator. The stainless steel elements are ground to close tolerances to provide a low profile. The antenna is designed to operate at both UHF and VHF frequencies, speeds up to 350 mph and altitudes up to 50,000 ft. It has a drag force of 0.92 lb @ 250 mph.
RAMI AV-100 ELT Antenna
This airborne antenna is intended for use with an ELT (Emergency Locator Transmitter) for general aviation. It has a passive two frequency wire whip, designed for low speed aircraft (up to 250 knots). This antenna operates at VHF and UHF frequencies. It has met DO-160G, Section 8, Category U requirements for robust vibration and is qualified for installation on helicopters with unknown related rotor frequencies.
CI 503 GS ANTENNA COUPLER/BNC Female Connector, 329-335 MHz, 50 Ohms
RAMI AV-21 Special Use | UHF
RAMI AV-532L VOR/LOC/GS Receive Only Antenna
The AV-532L is a VOR/LOC/GS receive only antenna. It consists of taper ground high-strength 17-7PH stainless steel elements to reliably withstand vibration and wind loads. The insulators are weather-sealed compression-molded bakelite with the mounting holes provided. The unit may be mounted with the V pointed either forward or aft. The antenna is designed to operate at speeds up to 350 mph and altitudes up to 50,000 ft. It has a drag force of 3.42 lb @ 250 mph. A 30 foot transmission line with integral balun is also supplied.
RAMI AV-14 Airborne Communications | VHF
CI 102 MARKER BEACON ANTENNA /BNC Connector, 75 Mhz, 50 Ohms, 4 hole internal mount, Airspeed 400 Knots. Includes gasket C10208, & a White Finish
The CI 102 marker beacon antenna is designed for use with modern, high sensitivity marker beacon receivers. Small and lightweight, this marker beacon features 4-hole internal mounting for simple installation. The antenna assembly is enclosed in an injection molded radome which is impervious to the tough environments typical of the underside of an aircraft. DC grounded to minimize accumulation of precipitation static.
MARKER BEACON ANTENNA COUPLER/BNC Female Connector, 75 MHz, 50 Ohms
VHF Communications Antenna | 118-137 MHz, 4-Bolt Mount, BNC Female Connector, Gloss Black
The AV-10 VHF communications antenna is designed for high-performance aircraft applications. It exhibits excellent electrical characteristics and incorporates an efficient aerodynamic 4-bolt mounting base. The antenna essentially matches the styling of the communication antenna currently used on most single and light twins. The antenna is designed to operate at speeds up to 350 mph and altitudes up to 50,000 feet. It has a drag force of 2.70 lbs @ 250 mph. This antenna is a direct replacement for the CI 121.
This antenna comes in gloss black.
DME TRANSPONDER ANTENNA/BNC Female Connector, Extended 2 Stud Mount, .70 Stud Length, 960-1220 MHz and 1030-1090 MHz, 50 Ohms, Airspeed 400 Knots & a White Finish
The CI 105-16 is a broadband and rugged antenna designed for DME or transponder use. The antenna assembly is designed specifically as a replacement for the Honeywell Bendix-King KA60 and offers an extended length, two-stud mounting that is found on the KA60. It includes a BNC connector and covers 960 MHz to 1220 MHz frequencies and is rated to 400 Knots TAS at 70,000 feet.
RAMI AV-587 Antenna Accessories | Diplexer, Splitter
CI 105 DME TRANSPONDER ANTENNA/BNC Female Connector, L-Band, 960-1220 MHz and 1030-1090 MHz, 50 Ohms, Airspeed 400 Knots, cork gasket included, 2 Hole Mount & a White Finish
The CI 105 is a broadband and rugged antenna designed for DME or transponder use. The antenna assembly is encased in a glass reinforced polyester molded shell and has a standard two stud mounting configuration. It includes a BNC connector and covers 960 MHz to 1220 MHz frequencies and is rated to 400 Knots TAS at 25,000 feet.
